24/7 EMERGENCY RESTORATIONPortland, OR & Vancouver, WA
SuperiorWater & Fire
Restoration
Menu

BURST PIPES · VANCOUVER & PORTLAND

Pipe burst? Shut the water off first.

A split supply pipe keeps releasing water until the valve feeding it is closed. Superior helps with water removal, moisture checks and structural drying in Vancouver, Portland and nearby communities. A plumber repairs the pipe.

Can’t call? Request a callback ↗

24/7 help. Confirm the current arrival time when you call.

In this guide
Superior Water & Fire Restoration service van

YOUR LOCAL RESTORATION COMPANY

Superior Water & Fire Restoration

Family owned and operated, based in Vancouver and serving the Portland metro. We help you understand the damage and the next step.

Meet Superior

THE FULL FIRST-RESPONSE GUIDE

What to do when a pipe bursts, in order.

  1. Shut off the water to the house.

    Close the main shutoff valve using the instructions below. A burst supply pipe keeps flowing at full pressure until it is isolated, so this comes first when you can reach the valve from a dry, safe position. If the valve is in a flooded basement or crawl space, or water is falling on the electrical panel, do not go in. Call a plumber or your water provider to shut the water off at the street.

  2. Keep away from water near electricity.

    Water from a broken pipe often reaches outlets, light fixtures and appliances. Do not touch wet electrical equipment. If there is standing water, turn off the main power only when the panel and your route to it are dry. Otherwise have an electrician or the utility isolate it. Have affected wiring and equipment checked before it is used again.

  3. Stay out from under wet ceilings.

    A ceiling that is bulging, sagging or dripping is holding water and can come down without warning. Keep people and pets out of that room. Do not push on the bulge or stand under it to place a bucket.

  4. Relieve the remaining pressure.

    With the main valve closed, open cold faucets, starting on the lowest level you can safely reach. This drains water left in the pipes and reduces what comes out at the break. It also confirms that the valve is holding. Do not loosen fittings or try to clamp the pipe near the break.

  5. Record the damage and protect what is dry.

    Photograph the break, each wet room and any ceiling stains from a safe position. Note when you found the leak and when the water was shut off. Move dry belongings, rugs and electronics out of the water’s path if you can do so without walking through standing water or under a wet ceiling.

  6. Call a plumber and arrange a moisture assessment.

    A licensed plumber repairs or isolates the damaged pipe. Arrange an assessment of the building at the same time. Drying should start promptly, and repairing the pipe does not dry the wall. Do not rely on surfaces feeling dry. Moisture-meter readings help identify which walls, floors and ceilings took on water and how far it traveled.

IDENTIFY WITHOUT RESTORING PRESSURE

Where the pipe broke changes what you check.

You do not need to find the exact break before closing the main valve. These clues help you describe the problem to the plumber and to us.

Possible sourceWhat you may noticeWhat to do
Pipe in an exposed areaWater sprays or runs from a visible pipe in a garage, basement, utility room or under a sink.Close the main valve, or the fixture valve when the break is clearly after it. Keep clear of nearby electrical equipment. Tape or a clamp on a pressurized pipe is not a repair.
Pipe inside a wall or ceilingYou hear running water with every fixture off, a wall or ceiling stain grows, or water comes out at a baseboard, outlet or light fixture.Close the main valve. Keep away from wet outlets and fixtures and do not cut into the wall. Tell the plumber where water first appeared.
Frozen pipe that thawedAfter a hard freeze a faucet gave only a trickle. Later, water appeared in a crawl space, garage, attic or outside wall.Close the main valve. More than one section may have split, so ask the plumber to check the other pipes that froze before pressure is restored.
Outdoor faucet or its supply pipeWater runs along the foundation or inside the wall behind an outdoor faucet, often when it is first used after winter.Close the faucet and its indoor shutoff if it has one, or the main valve. Check the room, crawl space or basement behind that wall for water.

FIND IT · CLOSE IT · CHECK IT

How to find and close the main water valve.

If you are reading this before an emergency, find the valve now and check that it turns. Only operate a valve you can reach from a dry, safe position.

  1. Look where the water line enters the home.

    The main valve is usually on the supply pipe near where it comes in: in a basement, garage, utility room or crawl space, or outside near the foundation. Some apartments, manufactured homes and older houses have no accessible valve of their own.

  2. Close it gently.

    A lever valve closes with a quarter turn, so the handle sits across the pipe. A round handle closes clockwise and may take several turns. Stop if the valve is stuck, leaking or will not turn by hand. Forcing an old valve can break it.

  3. Ask for a shutoff at the street when you need one.

    If there is no house valve, it has failed or it is somewhere unsafe, call your water provider and ask for the water to be turned off at the meter. A plumber can also do this. In a shared building, call the property manager.

  4. Confirm the flow has stopped.

    Water from an open faucet should slow and stop. Water already in the pipes, wall or ceiling will keep draining for a while. If the leak continues at full flow, the valve is not holding or does not control that pipe. Leave it closed and call for help.

Typical quarter-turn lever valveThe handle position shows the usual open or closed position. Follow the markings on your valve.

Open · Along the pipe

Closed · Across the pipe

A round multi-turn handle is different: gently turn it clockwise until snug. Never force a stuck valve.

AFTER THE SOURCE IS CONTROLLED

What you can safely do before help arrives.

Water from a supply pipe starts clean, but there is usually far more of it than a spill. These steps apply only after the water is off, the area is electrically safe and no ceiling is sagging. They limit the damage. They do not replace drying the wall, floor or ceiling the water entered.

  1. Pick up water from hard floors.

    Use towels and a mop on intact hard flooring. Do not use an ordinary household vacuum, and do not run cords through wet areas. Wring out or remove soaked towels so they do not hold water against the floor.

  2. Lift what is standing in the water.

    Move rugs, boxes, books and light furniture off wet floors where you can do so safely. Wet cardboard and paper hold water against flooring and should come out of the room.

  3. Leave walls and ceilings closed.

    Do not cut drywall, pull baseboards or remove insulation to look for water. An opening in the wrong place can hit wiring or plumbing. Note where a wall is stained, soft or swollen and report it.

  4. Keep the heat on and ventilate.

    After electrical safety is established, normal heating and a suitable dehumidifier help limit moisture in the air. In freezing weather, keeping the home heated protects the other pipes. Room fans help exposed surfaces only. They do not dry a wall cavity or the layer under a floor.

WHERE THE DAMAGE CAN SPREAD

Pressurized water travels fast and far.

A burst pipe can release a large amount of water before anyone reaches the valve. Much of the damage is often in places you cannot see from the room.

Moisture meters show where the water went

Do not judge the damage by which surfaces feel wet or dry. Water from a pressurized pipe runs inside wall cavities, under flooring and along framing. Superior uses moisture meters to help determine how far the water traveled and which materials are affected. Follow-up readings guide the drying plan.

Inside the wall and the next room

A pipe that splits inside a wall can wet the insulation, the back of the drywall and the framing at the floor before a stain shows. The room on the other side of that wall is often affected too.

Floors below and ceilings

Water from an upper-floor or attic pipe can enter the floor assembly and collect above the ceiling below. Possible water entry into a floor or ceiling assembly warrants assessment even when there is no visible stain.

Crawl spaces, garages and attics

Pipes most often freeze in unheated spaces. A break there can run unnoticed, soak insulation and pool on the ground cover. Do not enter a wet crawl space or attic to look. Describe what you can see from the access.

HOW SUPERIOR HELPS

From the shutoff to a drying plan.

Tell Superior where the pipe broke, how long the water ran and which rooms it reached. A plumber repairs the pipe. Superior handles the water in the building.

  1. Map the affected materials

    Inspect accessible walls, floors and ceilings in the affected rooms and in the rooms beside and below them. Use moisture meters to help trace the water beyond the visible wet area.

  2. Remove water and address wet materials

    Extract standing water where safe. Explain which materials can be dried in place and which, such as saturated insulation or swollen trim, may need removal for access or because of damage.

  3. Dry the structure and check progress

    Set drying equipment for the affected rooms and cavities. Use follow-up moisture readings to judge drying progress and explain what repair work remains.

KEEP THE FACTS TOGETHER

Keep a record of the break and the damage.

A clear record helps the plumber, the restoration crew and your insurer understand what happened. Ask your insurer what it needs. Coverage depends on your policy and the facts.

  • When you found the leak, when the water was shut off and, if known, when the plumbing last worked normally.
  • The weather if freezing was involved, and whether the home was occupied and heated.
  • Photos of the broken pipe or the place water appeared, each affected room, ceilings below and damaged belongings.
  • The plumber’s findings and invoice, including where the pipe failed and what was repaired. Ask the plumber to leave the failed section with you in case your insurer wants to see it.
  • The restoration scope, moisture-check and drying records, and a list of materials removed.

REPAIR · CLEAN · CONFIRM DRYING

Before the water goes back on and the walls are closed.

  • Have the plumber repair or cap the damaged pipe, and check other pipes that froze, before the main valve is reopened.
  • Reopen the main valve slowly with someone watching the repair and the rooms below. Close it again if a new leak appears.
  • Have water-affected wiring, outlets, fixtures and appliances checked before they are used.
  • Ask for the moisture-meter findings for the affected walls, floors and ceilings. Confirm that those materials have dried to the restoration criteria before insulation, drywall or flooring is replaced. Touch cannot establish that.
  • Report new stains, odors, soft spots or drips. Water inside a wall or floor can keep moving after the pipe is fixed.

Start drying promptly after safe cleanup. EPA recommends drying water-damaged materials within 24–48 hours to reduce mold risk. Do not wait 48 hours to act. Drying time varies with the materials and conditions. If materials stay damp, the water is contaminated or the leak’s age is unknown, get an assessment.

AFTER THE IMMEDIATE PROBLEM

Lower the chance of another burst pipe.

  • Find and label the main water valve, and check once a year that it turns.
  • Before a hard freeze, disconnect garden hoses and insulate exposed pipes in the crawl space, garage and attic.
  • Keep the heat on when you are away in winter. During a cold snap, open cabinet doors under sinks on outside walls.
  • When temperatures stay below freezing, let a slight drip run from faucets served by pipes in unheated spaces.
  • Ask a plumber about pipes that have frozen before, corroded fittings or old supply lines. A leak alarm warns you. Only an automatic shutoff device stops the water.

QUESTIONS BEFORE YOU CALL

A few things you may be wondering.

The pipe is frozen but not leaking. What should I do?

Leave the faucet open and warm the pipe gently with a hair dryer, an electric heating pad or towels soaked in hot water. Never use a torch or any other open flame. Call a licensed plumber if you cannot find or reach the frozen section. Watch the area as it thaws, because a split often shows only when water flows again.

Can I turn the water back on to find the leak?

Not until a plumber has repaired or isolated the damaged pipe. Restoring pressure sends more water into the same wall or floor. If you need water in the house, ask the plumber whether the damaged branch can be capped first.

The wall looks fine. Does it still need checking?

Yes, if the pipe ran inside or above it. Drywall and paint can look normal while the insulation and framing behind them are wet. Moisture-meter readings help show whether the wall, the floor below it or the next room is affected.

Who fixes the pipe?

A licensed plumber repairs the pipe. Superior removes the water and dries the building. Call both. The water needs to be off, or the damaged pipe isolated, before drying can work.

Sources and further detail

General safety and equipment references checked November 17, 2026. Use the instructions for your exact appliance or valve when they differ.

24/7 EMERGENCY RESTORATION

Let’s work out the next step.

Tell us where the pipe broke, whether the water is off, how long it ran and which rooms or ceilings are wet.

Call to confirm service availability and arrival time for your address.

Request a callback